Cases / Power / Portability

Hi there, I am currently thinking about getting a Make Noise 104HP Skiff for a system of Cortex, Polar, Marbles, 4MS Buff x2, Bridge x2, Arch and Shapechanger. Do you think this would be ok to fit in that skiff and to be powered by the Make Noise power supply? Many thanks!

The make noise power supplies are not officially endorsed by LZX (to my knowledge)
You might want to look into a Malekko Power

Have you set up your desired modular setup on modular grid?

https://www.modulargrid.net/e/modules/home

That way you can get a sense of what sort of power draw the assortment of modules you’re wanting to use will require. It’s not always 100% accurate, so looking at the manuals to verify power requirements is always the best practice. And like @DesertMuseum mentions, the Make Noise power system may not be the best choice for video modules. However, I did use one for awhile and it was passable for my needs at the time. Good luck in your search!

Hi there, thanks so much for the feedback. The Thing is I am looking for a 104HP 3U row with he right kind of power. About £300, anyone know of anything like this that is good for video? Many thanks!

Im looking into the Befaco JumpSkiff, mostly because of size (98HP, 52mm deep), which will be ideal for Orion.
The topology of the power supply should be fine for video, but it has only 0.6A.
Extra hole to power the fpga with a second brick? Bigger brick?
Anyone experience with it?
VideoFanatic, what you can also do is to get a moog mother case or similar that comes with no power and fit any of the PSU recommended by Lars.

Hello, in the last week I’ve upgraded my main live-performance case from a 6u bento-box with a synthrotek deluxe power w a 5a meanwell supply, which could easily fit castle/cadets, to get this; a enclave 6u w a make noise bus and 4.3a volgen supply. while not a complete upgrade, ive notice zero change-over in terms of power and Ive got more modules in the enclave than on the bento.

however, if yr trying to fit castle/ cadets into a skiff like ive now got, try buying longer screws from yr local hardware store and mount a set of nuts between the bottom of the module and the edge of the rail. depending on the depth, you may need to apply 2-3 nuts. the ramps I have there only uses 1 set of nuts and barely fits in the deepest end of the case, but it’s enough space.

what type of Volgen powersupply did you get? (and where did you buy it?) I’m looking for a new one too.

https://www.digikey.com/product-detail/en/volgen-america-kaga-electronics-usa/KTPS65-1543DT-3P-VI-C-P1/62-1222-ND/5247775

for the record, that is the power supply that ships w the new make noise steel cv bus cases.

Another case inquiry. I seem to remember that a lot of early LZX systems were housed in Monorocket cases. Is it safe to say their power supplies were generally suitable for video purposes. I do believe they were linear.

Their linear supplies worked great (IIRC, the 6U case had enough power for LZX but 9U case that had the same PSU needed some augmentation.) There was a period when they were using Meanwell supplies that were not so great. I’m not sure what’s being used in them now.

2 Likes

I don’t think they are made anymore. Still in search of a good 9u Utility case with sufficient power.

Anyone know how well Trogotronic’s power supplies work for video? They’re pretty high amperage for sure, and they claim to be very clean power, but has anyone tried them out?

Has anyone tried putting the Malekko power in a 3u 104hp case? From the specs there should be enough room, but I’m not quite sure if it will be to tight with cables and all.
I’ll want expand to two rows in the future so it would be nice to invest in a good power supply from the beginning.

3U full of LZX modules would be too much. Malekko Power is suitable for up to 208HP. Budget about +/-10mA per HP for LZX systems.

Have had terrible reports about switching noise from the Trogotronic.

@creatorlars think you’re mixing up 3u and 3 rows here

@jkbh - as lars said it’s good for 208hp, it’ll be fine for 104hp

1 Like

Yes, you’re right, I meant 3x 3U rows. So with 104HP rows, that’s 312HP. Recommended you power this with two powered boards supplying at least around 1.5A each.

1 Like

MDLR are using a different power supply now and are no longer offering the Doepfer PSU3 option. I just got off the phone with him and he said the new power supply for the Performer series Pro (Meanwell GSM60A18-P1J with MDLR PWR 45W powered buss boards) is actually less noisy than the Doepfer. Can anybody confirm that this is a good choice for video synthesis?
And what would be a good ‘torture test’ to check the suitability of a modular case for video?

1 Like

I see now that with only 1.2A on the -12V rail, like the Doepfer PSU3, it would be a bit light for 208HP anyway :frowning:

1 Like